Activity Stream

Filter
Sort By Time Show
Recent Recent Popular Popular Anytime Anytime Last 7 Days Last 7 Days Last 30 Days Last 30 Days All All Photos Photos Forum Forums Groups Groups
  • Chris from Washington's Avatar
    3 Weeks Ago
    Welcome to the forum!
    1 replies | 73 view(s)
  • ckirocz28's Avatar
    3 Weeks Ago
    A more appropriate version, but I finally remembered and you got the idea. https://www.radioshack.com/products/radioshack-8-ohm-non-inductive-resistor Sent from my SM-G935U using Tapatalk
    5 replies | 163 view(s)
  • shiftazz's Avatar
    3 Weeks Ago
    That's exactly what I needed. Thank you a lot for your help.
    5 replies | 163 view(s)
  • ckirocz28's Avatar
    3 Weeks Ago
    You'll still need them on separate channels (head unit or amp) to adjust their levels separately from the mids. Or you could get some audio type resistors and wire them inline with the tweets, I...
    5 replies | 163 view(s)
  • Pekoh's Avatar
    3 Weeks Ago
    Pekoh here. Joined up as I am back setting up a new car and have no idea what's in the market these days. Has been years since I set up my kist Sent from my SM-G950F using Tapatalk
    1 replies | 73 view(s)
  • Pekoh's Avatar
    3 Weeks Ago
    Pekoh replied to a thread Low volume in Car Audio Discussion
    How did you get on? I saw this and had a few thoughts, poor earth on the amp, reversed polarity (ie. Positive from amp on the negative terminal of speakers amd visa versa). High/low pass setting on...
    1 replies | 143 view(s)
  • shiftazz's Avatar
    3 Weeks Ago
    Yeah, forgot to mention, I did use capacitors as crossovers on both tweeters.
    5 replies | 163 view(s)
  • ckirocz28's Avatar
    3 Weeks Ago
    You've made a technical error, your tweeters should be connected through a passive crossover along with the mids, or to separate channels on the amp or a different amp, or to the headunit if nothing...
    5 replies | 163 view(s)
  • shiftazz's Avatar
    3 Weeks Ago
    Thanks a lot for the answer. For now I'll take the risk, the amp has many protections in it, so I hope it won't get damaged. Later on, I'm thinking on connecting the mid-speakers in series and then...
    2 replies | 156 view(s)
  • shiftazz's Avatar
    3 Weeks Ago
    So, I just got my new budget tweeters and connected them to my amp in parallel to two mid-speakers. The thing is, the tweeters are now too loud, and I lack the mids. Just wanted to know if there is...
    5 replies | 163 view(s)
  • Chris from Washington's Avatar
    3 Weeks Ago
    Hi Welcome to the forum, Just to make sure I understand it, but you want to have all 3 in Parallel per channel? so 2 4ohms and an 8ohm? Yes that will give you around 1.6 ohms. It's...
    2 replies | 156 view(s)
  • shiftazz's Avatar
    3 Weeks Ago
    So I have already connected 2 original and 2 new mid-range speakers in parallel and a subwoofer on a different channel to my amplifier. I want to connect two more tweeters to the same channels as the...
    2 replies | 156 view(s)
  • sharcox4's Avatar
    4 Weeks Ago
    This receiver is Siriusxm ready. We installed the V300C Connect Vehicle Tuner. So I pressed on "Source" to bring up the Siriusxm mode. It will show Pandora, iHeart radio, and others, but not...
    0 replies | 67 view(s)
  • Bobby8907's Avatar
    4 Weeks Ago
    I have a 2013 Honda accord and im installing my two JL audio 12' subs and im using a LC2i (Line output converter) i was able to pull the factory stereo and tap into the 12 volt power wire to use as a...
    0 replies | 74 view(s)
No More Results
[Output: 34.61 Kb. compressed to 31.93 Kb. by saving 2.68 Kb. (7.74%)]