Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

wiring problem for sub

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: wiring problem for sub

by okayyyy » Sun Jan 08, 2006 3:52 pm

smoker wrote:you are basically making the amp see 1 4 ohm load....take the negative of one coil to the amps negative......take the positive of the other coil to the amps positive then run a jumper between the to leads that are left on the speaker..........


thank you so much! that did 'er!

by smoker » Sun Jan 08, 2006 12:01 pm

okayyyy wrote:does it matter which lead goes back to the amp?

you are basically making the amp see 1 4 ohm load....take the negative of one coil to the amps negative......take the positive of the other coil to the amps positive then run a jumper between the to leads that are left on the speaker..........

by Bwcad1 » Sun Jan 08, 2006 11:44 am

check out bcae1.com that has a lot of information about series parallel wiring and plenty of other info!

by okayyyy » Sun Jan 08, 2006 11:31 am

Ryan from Ohio wrote:You want to series the dual 2 Ohms to get a 4 Ohm nominal.
Put the sub so one coil is on the left, the other on the right.
Now pull some speaker wire so its just one wire on each side, enough to reach each side.
Put one lead on one sides +, the other on the opposites -
Then run just a single piece runner between the leftover + and -
done

does it matter which lead goes back to the amp?

by Bwcad1 » Sun Jan 08, 2006 7:44 am

thanks ryan! i think i fell asleep lol

by Ryan from Ohio » Sun Jan 08, 2006 5:46 am

You want to series the dual 2 Ohms to get a 4 Ohm nominal.

Put the sub so one coil is on the left, the other on the right.

Now pull some speaker wire so its just one wire on each side, enough to reach each side.

Put one lead on one sides +, the other on the opposites -

Then run just a single piece runner between the leftover + and -

done

by okayyyy » Sat Jan 07, 2006 9:42 pm

Bwcad1 wrote:what is the voice coil ohm rating on the sub? what kind of amp are you running it on? what is the minimum inpedence of the amp?
dual 2ohm voice coil, min inpedence is 4 ohms, and im running it on planet audio dx400 amp

by Bwcad1 » Sat Jan 07, 2006 9:15 pm

what is the voice coil ohm rating on the sub? what kind of amp are you running it on? what is the minimum inpedence of the amp?

wiring problem for sub

by okayyyy » Sat Jan 07, 2006 9:08 pm

i have a hifonics atlas 12sq.. a 13 inch square sub, and the wiring diagram that came with it, doesnt make sense.. i need to know where to route the speaker wire for 4ohm. can anyone help me??

Top