Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

Help with Orion 2500D

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: Help with Orion 2500D

by GlassWolf » Tue Nov 08, 2005 1:50 am

where did you get the amp?
was it new or used?
Im wondering if you got a defective amp.
without having it on a bench I cant tell ya for sure

by Livinloud » Sun Nov 06, 2005 12:09 pm

KikiTheCat wrote:LPF @ 60Hz
SSF @ 45Hz
wire the coils in parallel and use one set of speaker terminals only on the amplifier.
see how it does.
make sure gain is set properly.
I got my sub wired positive to positive with 1 wire coming out of the box into the terminals on the amp and the same with the negative.

My sub still sounded better and was louder with my Kicker amp.

I dont get it.

by GlassWolf » Sun Nov 06, 2005 4:29 am

LPF @ 60Hz
SSF @ 45Hz
wire the coils in parallel and use one set of speaker terminals only on the amplifier.
see how it does.
make sure gain is set properly.

by Livinloud » Sat Nov 05, 2005 3:47 pm

Bwcad1 wrote:turn the high pass filter off and put the low pass filter on. the amp should have where to bridge marked on the side or in the manual. the master copy is for strapping the amps unless you have more than one leave it on master. match the gain to the pre out voltage of your head unit. correct me if im wrong on any of this stuff o great and powerful stereo gods! (mhmm ryan, justin, kiki, terry or devin.)

I cant turn the high pass filter off because that is the SSF.
Ryan from Ohio wrote:Depends on the Ohm load and if you have it wired right.

Cant you download a manual online?
Well I finally download the manual and got it to open.

It says that the speaker terminals are paralled inside the amp. I'm guessin that it doesnt matter which ones you use then?

Well I still dont understand this amp. Maybe I should just return it and get my 1200.1 fixed again.

by Livinloud » Sat Nov 05, 2005 2:48 pm

Ryan from Ohio wrote:Depends on the Ohm load and if you have it wired right.

Cant you download a manual online?
Well I finally download the manual and got it to open.

It says that the speaker terminals are paralled inside the amp. I'm guessin that it doesnt matter which ones you use then?

Well I still dont understand this amp. Maybe I should just return it and get my 1200.1 fixed again.

by Ryan from Ohio » Sat Nov 05, 2005 2:30 pm

Depends on the Ohm load and if you have it wired right.

Cant you download a manual online?

by Livinloud » Sat Nov 05, 2005 2:29 pm

I think I have it right this time, but wouldn't you think the output would be more than the Kicker 1200.1?

by Bwcad1 » Sat Nov 05, 2005 1:23 pm

isnt 30 hz setting on the ssf kinda low for a box tuned that high??? just wondering not questioning you at all oh great one!!! :bow

by Ryan from Ohio » Sat Nov 05, 2005 1:21 pm

Set it on LPF

Set the LPF to about 80-90Hz

Set the SSF (sub sonic filter) to about 30 Hz

Set the gain to 3/4 way

Set it to 12 dB roll off for starters...

That should get you started...

by Bwcad1 » Sat Nov 05, 2005 1:19 pm

turn the high pass filter off and put the low pass filter on. the amp should have where to bridge marked on the side or in the manual. the master copy is for strapping the amps unless you have more than one leave it on master. match the gain to the pre out voltage of your head unit. correct me if im wrong on any of this stuff o great and powerful stereo gods! (mhmm ryan, justin, kiki, terry or devin.)

Top