soo.. truck was on fire..

Scarrell · Post by **Scarrell** » Tue Oct 14, 2008 7:47 pm

well guys, i bought a good running 305 out of a 88 Monte Carlo for $100, and my motor is tore down and will be takin out in a couple days.. so.. wish me luck.. ill keep yuns updated

MobileAudio219 · Post by **MobileAudio219** » Tue Oct 14, 2008 8:25 pm

Scarrell wrote:well guys, i bought a good running 305 out of a 88 Monte Carlo for $100, and my motor is tore down and will be takin out in a couple days.. so.. wish me luck.. ill keep yuns updated

Don't take this wrong way, but I seriously doubt the 305 is going to make you happy, it's barely a set-up from a 4.3.

I'd do a 350, or just go back with another 4.3. The 305 is a decent engine, but doesnt isnt exactly a power house.

Ryan from Ohio · Post by **Ryan from Ohio** » Wed Oct 15, 2008 3:18 am

Eh for $100... What the heck.

cargodz · Post by **cargodz** » Wed Oct 15, 2008 4:04 am

MobileAudio219 wrote:I'd do a 350, or just go back with another 4.3. The 305 is a decent engine, but doesnt isnt exactly a power house.

Well sure if you could find a 350 in good running shape for $100, but don't put down that little 305 quite so fast either... They actually have a lot of potential.
Before you drop it in go have that that thing bored 30 over and get some new pistons, rods, port and polish with all new goodies in the top and I'll tell you what... That lil 305 will scream... and since it's lighter than the 350 you've got a weight advantage

Bwcad1 · Post by **Bwcad1** » Wed Oct 15, 2008 4:13 am

cargodz wrote:Well sure if you could find a 350 in good running shape for $100, but don't put down that little 305 quite so fast either... They actually have a lot of potential.
Before you drop it in go have that that thing bored 30 over and get some new pistons, rods, port and polish with all new goodies in the top and I'll tell you what... That lil 305 will scream... and since it's lighter than the 350 you've got a weight advantage

all that work and you got a lightweight 350

cargodz · Post by **cargodz** » Thu Oct 16, 2008 4:28 am

Bwcad1 wrote:all that work and you got a lightweight 350

Basically yes, but with a ton more torque... I did all this to my old 1984 Trans-Am with a 305 and those were considered to be the dog years for the F-bodies... Had a custom made 383rear for it so it would do street and track, best quarter was 12.26 (without the nitrous) with street rubber.
So like with any motor, the 305 has potential if you put the money into it.

Bwcad1 · Post by **Bwcad1** » Thu Oct 16, 2008 4:42 am

blood sweat and tears.

cargodz · Post by **cargodz** » Fri Oct 17, 2008 6:04 am

Bwcad1 wrote:blood sweat and tears.

Just like any other good build up as it should be :happy055:
If making a badass car outta nothing was easy everybody would have one... Oh that's right, according to some kids it is easy... Fatpipe (not full exhaust), Tuners rims, Intake, and stickers and a Honda will do 8's in the quarter LOL

Scarrell · Post by **Scarrell** » Sat Nov 22, 2008 6:38 pm

update and what not.. scratched the v8 altogether and have a 4.3 in my truck already and running, out of a 99 Blazer with 60,??? miles... runs fine...etc.. a tire or two is square though since it sat so long, now it will sit again til its warm enough to drive it around to get the tires warmed up to even em out. im not driving around in this cold crappy weather, because it will take like 4 times longer and all that.. but on a side note i may sell it or trade it for a Car.. yes a car.. i never liked cars(even though ive had a couple before).. because of trunk rattle.. but i put my system in the womans car and ive grown used to the car thing again and may go that direction eventually.

MobileAudio219 · Post by **MobileAudio219** » Sat Nov 22, 2008 8:19 pm

but don't put down that little 305 quite so fast either... They actually have a lot of potential.

Theres no doubt you can make one fast...

Before you drop it in go have that that thing bored 30 over and get some new pistons, rods, port and polish with all new goodies in the top and I'll tell you what...

The only real reason to bore the block is to clean up the cylinder walls, the little bit of added displacement isnt going to gain you much, if anything at all...

The stock 305 heads arent even worth porting...

That lil 305 will scream... and since it's lighter than the 350 you've got a weight advantage

Theres no doubt you can make them scream, but I'm not really sure its worth it...

Thats why the 305 to 350 swap is so popular, it gets you more for less!!!