Attention all members!
Have a cool ride? Then show it off on our website! All vehicles welcome!

Mmats hc100d

Post a reply

Confirmation code
Enter the code exactly as it appears. All letters are case insensitive.
Smilies
:awesome: :argh :ditto :inout :words :bow :cheers: :bigwink: :fing02: :sad017: :scorp: :o :D ;) :p :unwell028 :tongue017 :thumbsup :surprised :sm29: :angry011: :angry015: :angry012: :nono: :angry010: :nono :banghead :mad: :dif :angry :CRZ_13: :eek: :confused: :confused0 :confused :( :sad: :cool: :dance :mecry: :jesterlol :embarrass :flame: :doh :evil019: :evil001: :rolleyes: :sub:
View more smilies
BBCode is ON
[img] is ON
[url] is ON
Smilies are ON
Topic review
   

Expand view Topic review: Mmats hc100d

by Bwcad1 » Wed Jun 14, 2006 9:41 am

no offence dude but these posts are really old.

by donpisto » Wed Jun 14, 2006 9:38 am

jejuanm wrote:I have a Mmats hc 100d, Anyone know what the this amp will do at .05 ohms. Also is it worth running it at .05 ohms. I have have 4-12" DVC 4 ohm ratings. I wondering if this amp will do the job, or do i need another amp. I have a Autotek MX5000 but i had to take that beast out of my explorer, it was killing the electrical system. So im looking for some great input here, and the subs are Kicker
L series.
I'm not sure what it would do at .5 ohms but I dont recommend running it at .5 ohms, even though the mmats can get that low. any time you decrease the ohms, your increasing instability. amps are more stable at higher ohms. I guess if you dont push it too much then you would be fine, but be careful, if the ohm level drops below .5 often say goodbye to the amp

by High Society » Mon Apr 17, 2006 12:24 pm

http://www.rockfordfosgate.com/rftech/w ... 4+ohms+x+2

This is how you wire it up for a 2 ohm load.

by OnYrMrk » Mon Apr 17, 2006 11:39 am

I figured as much...no skin off my rear...

by Bwcad1 » Mon Apr 17, 2006 10:30 am

sorry joe not yellin just me im a draftsman everything is in caps...

by OnYrMrk » Mon Apr 17, 2006 10:26 am

geez, bill...you don't have to yell...btw..my 225's ran .5ohm all the time.

no need for burps with actual music...LOL

by Bwcad1 » Mon Apr 17, 2006 9:04 am

THERE ARE A LOT OF AMPS THAT CAN DROP THAT LOW BUT ONLY ON BURPS HELL MY mm4000.1 IS RATED AT 2 OHM BUT I CAN DROP IT TO .7 OR EVEN .5 FOR BURPS IT WILL RUN DAILY AT 1 OHM NP AND DOESNT GET WARM.

by OnYrMrk » Mon Apr 17, 2006 9:02 am

The ONLY amps I would trust at .5 ohm is Adcom and Orion's 225 HCCA's those amps are Bullet Proof!!!!

The 225 HCCA is .25ohm stable, but runs much better at .5 ohm too.

by Bwcad1 » Mon Apr 17, 2006 8:04 am

well playing it at a moderate level is fine because your reactive load is gonna be higher you probably up around 1.5 2 ohm anyways. i just dont reccomend it because playing it there will take a toll on the amplfier over time. bcae.com wiring help

by jejuanm » Mon Apr 17, 2006 7:14 am

Bwcad1 wrote:actually did some checking that amp isnt stable to .5 ohm and will protect at anything less than 1 ur best bet is to wire it at 2 ohm. and go from there.
Im playing it at .5 now, it dosent get hot, it just shuts down after a good 5 mins of comp play, and then will kick right back in lees than a min. May be thats the .5 burp you get, but I can play it all day at a moderate level with good pounding bass. I figured i dont have enough power for this thing to pound at .5 ohms. I have had it running like this since XMAS

Top