type r qestion

MobileAudio219 · Post by **MobileAudio219** » Fri May 12, 2006 8:02 pm

Ryan from Ohio wrote:I usually goto Lowes. Here they give you two free cuts then its $0.25 a cut thereafter...
So you may end up paying $3-5 for the cuts. Trust me though, this is much faster than trying to do it at home with a circular saw...

The lowes and home depots around here suck at cutting, usually way off....

And a dual 2ohm sub can only be wired to either 1 or 4 ohms, not 2...

fatmandan · Post by **fatmandan** » Sat May 13, 2006 11:23 am

i have just 1 voice coil wired and i check the resistane on it and it read 2 ohms..............

joeyc · Post by **joeyc** » Sat May 13, 2006 11:32 am

thats not going to work bro!! it must be wired using both coils! http://www.rockfordfosgate.com/rftech/w ... 4+ohms+x+2

EDIT: i just looked up your amp, it does 800 watts MAX @ 2 ohms, you couldn't get more then....maybe 500+ watts out of that amp IF you had a dual 4-ohm sub. You need to rewire it as well, it will damage the speaker with it wired like you have it. wire it at 4-ohms like it will show you on that link above, and consider getting a new amp that will give it maybe the 800 watts RMS not MAX

fatmandan · Post by **fatmandan** » Sat May 13, 2006 11:46 am

why would it mess it up? ive been running it like that for 3 weeks now and the sub is still doing good, it going to burn out the VC?

if so think this amp would work better? http://cgi.ebay.com/MTX-Thunder-801D_W0 ... dZViewItem

JeremyC · Post by **JeremyC** » Sat May 13, 2006 1:02 pm

Trust us, wire in the second coil or it will mess up the sub.

And get a diffrent amp. Once you rewire it with both coils you will bee looking at 4 ohms and maybe 400 watts, (probably less)

There is no way that amp will do 800 watts rms at 2 ohms. If the 250 is corect at 4 ohm then you could get 500 at 2

Even if it did you need something 1 ohm stable, or something putting out 800 watts rms at 4 ohm.

I stand corected, it will do 800 watts rms at 2 ohm, (moron on ebay messed up the 4 ohm reading) But it still won't work for you.

ridr4lif · Post by **ridr4lif** » Sat May 13, 2006 1:54 pm

Your best bet would probably be to find a 2 channel amp that puts out 800 rms, bridged at 4 ohms. You could also use a mono amp that puts out that much power at 1 ohm, but it will probably be more expensive.

fatmandan · Post by **fatmandan** » Sat May 13, 2006 9:09 pm

what you guys think of this amp since i cant run the MA?

http://www.woofersetc.com/index.cfm?fus ... ct_ID=1818

High Society · Post by **High Society** » Sat May 13, 2006 10:43 pm

NO....very cheap stuff. Wont do any of the nubers it stated. Please read our FAQ section and buy an amp using the good/bad/ugly list.

fatmandan · Post by **fatmandan** » Sun Jun 04, 2006 3:23 pm

Hey guys little up date i built the box scarrel post the plans to and i threw in a MTX thunder 4000 wred at 8 ohms on my new directed 600D amp

and it pounds i cant wait to get the alpine back some time this week