Another mustang???

MobileAudio219 · Post by **MobileAudio219** » Thu Oct 16, 2008 12:46 pm

I'm going to look at it saturday. It's an 88 gt, 5.0, 5 speed.

The guy sent me some pictures and it looks pretty nice, but I havent seen it in person so it's hard to say.

We've been talking back and fourth, and I think I'm going to trade my ranger for it (I have less than 500 bucks into the truck.)

The motor in the car is junk, but the rest of the car seems to be in decent condition.

I'm going to build a mild motor for it, 306 with gt40 heads and intake, stock h.o cam...

William from NOLA · Post by **William from NOLA** » Thu Oct 16, 2008 2:11 pm

It looks good on the outside.

MobileAudio219 · Post by **MobileAudio219** » Thu Oct 16, 2008 2:38 pm

Those are the pictures from his ad, he sent me pictures of the interior, it's a little dirty but should clean up nicely...

subster87 · Post by **subster87** » Thu Oct 16, 2008 3:00 pm

u thinking sleeper? or are you planning on making sure everybody knows ur put some work under the hood??? looks like its pretty good body shape? no rust?

MobileAudio219 · Post by **MobileAudio219** » Thu Oct 16, 2008 3:10 pm

subster87 wrote:u thinking sleeper? or are you planning on making sure everybody knows ur put some work under the hood??? looks like its pretty good body shape? no rust?

I'm leaving the body stock, might get some aftermarket 17" pony rims later on, the orginal pony's were 16".

The car already has the following mods:

Headers (not sure if the or shorties or long tube, or what brand)
Flowmaster catback
Short throw shifter
NEW King cobra clutch.

smoker · Post by **smoker** » Thu Oct 16, 2008 6:12 pm

nice deal man, i picked up a prochamber h pipe and a set of flowmasters with dumps for 50 bucks for mine...

NorthQuad · Post by **NorthQuad** » Thu Oct 16, 2008 6:46 pm

I'm jealous. I wouldn't mind having a '92 LX again. But with more than a 2.3L this time. I was in high school at the time, what can I say? Had the crappiest system in it too. But I tried. meh, mabey one day.

MobileAudio219 · Post by **MobileAudio219** » Thu Oct 16, 2008 8:03 pm

So heres the plans for the engine (if I get the car.)

Stock short block: New rings, main/rod/cam bearings, oil pump, freeze plugs, stock replacement timing chain.

H/C/I: Rebuilt Gt40 heads (maybe p's), GT40 intake (ported lower), stock h.o cam, 1.7 rockers.

I'd take the block to the machine to have the cam bearings replaced and the block checked, hopefully it wouldnt need to be punched so I could re-use the stock rotating assembly. I'd probably go ahead and replace the push rods and lifters as well..

I'd put it all back together with new gaskets/seals along with a fresh tune up...

Kind of a boring economy build, but should run good on 87 octane and should be speed density friendly... and be good for high 12's low 13's!

OnYrMrk · Post by **OnYrMrk** » Fri Oct 17, 2008 5:29 am

I just want mine to sound good, look good and if I need to get out of someones way in a hurry, then I can.

I have CarGodz to work with on this....Michael and I will be playing with this car.

Catback's, xpipe, maybe magnaflow side exit exhaust...
cold air kit, new plenum, overdrive pulleys, morel 3 way, Bill's WP 8's in trunk, All Audison amplification.

Bwcad1 · Post by **Bwcad1** » Fri Oct 17, 2008 5:40 am

side exhuast is illegal in most states now